Reliant FVIR GAS WATER HEATER Gebrauchs- und Pflegeanleitung PDF herunterladen (Seite 32)

STATUS LIGHT TROUBLESHOOTING FLOWCHART

LED FLASH

SEQUENCE

CONTROL STATUS CORRECTIVE ACTION

Six-Two Flash, three second pause Soft Lockout* - Recycle Limit - Flame Lost -

END Switch Fails

Turn the power switch on the gas control valve to the “OFF” position and unplug the power cord from the

power outlet.

1. Check all wiring connections to insure all harness and wire connections are seated firmly and provide

proper electrical contact. If no connection problems are found replace the damper. Firmly seat any

loose connections found. If any connections are found to be damaged consult the replacement parts

list on pages 34-35 for the appropriate replacement. After any connection problems are fixed restart

the water heater by following the lighting instructions on page 19. If the problem persists replace the

damper.

Six-Three Flash, three second pause Soft Lockout* - Recycle Limit - Flame Lost Turn the power switch on the gas control valve to the “OFF” position and unplug the power cord from the

power outlet.

1. Check the incoming gas line pressure to ensure adequate supply to the water heater. If incoming

gas supply pressure is adequate proceed to step 2.

2. Check all wiring connections and insure all harness and wires connections are seated firmly and

provide proper electrical contact. If no connection problems are found proceed to step 3. Firmly

seat any loose connections found. If any connections are found to be damaged consult the

replacement parts list for the appropriate replacement. After any connection problems are fixed

restart the water heater by following the lighting instructions on page 19. If the problem persists

proceed to step 3.

3. Check condition of the base ring filter and flame arrestor. If they are clogged follow the

instructions for cleaning on pages 26-27. If parts are not clogged proceed to step 4. After

cleaning follow instructions for lighting on page 19. If problem persists proceed to step 4.

4. Follow the instructions on page 25 to remove the burner assembly. Once the burner assembly has

been removed inspect the manifold tube and burner, see figure 29 , for any obstructions. If any

clogs or obstructions are present clear them. Inspect the electrode/flame sense rod, see figure

43 , for corrosion buildup, degradation, or damage. If there is evidence of any damage to the

electrode/flame sense rod replace the igniter/pilot assembly. Follow the directions on page 27 to

re-install the burner assembly into the combustion chamber. Follow the instructions for lighting on

page 19. If the problem persists contact a qualified service representative.

Six-Four Flash, three second pause Soft Lockout* - Flame out of Sequence Sensed Turn the power switch on the gas control valve to the “OFF” position and unplug the power cord from the

power outlet. Wait 10 minutes then follow the lighting instructions on page 19. If the problem persists

replace the gas control valve.

Seven Flash, three second pause Flammable Vapor Sensor (FVS) Lockout 1. Do not touch any electrical switch, do not use any phone in the building and do not try to light any

appliance.

2. Smell around the water heater to ensure there are no gas leaks at the gas control valve or in the

supply gas line or for any other type of flammable vapors in the area.

3. Carefully inspect the area surrounding the water heater for any substances such as gasoline,

paint, paint thinners, varnish, or cleaners that could emit flammable vapors. Remove anything that

can potentially emit flammable vapors from the area and store it properly in a different location.

4. Contact a qualified service representative for inspection and/or replacement of the FV sensor.

Eight-One Flash, three second pause Flammable Vapor Sensor (FVS) Fault Detected Turn the power switch on the gas control valve to the “OFF” position, wait 10-20 seconds then turn the

power switch on the gas control valve to the “ON” position. If the problem persists replace the gas valve.

Eight-Two Flash, three second pause Temperature Sensor Fault Detected Turn the power switch on the gas control valve to the “OFF” position, wait 10-20 seconds then turn the

power switch on the gas control valve to the “ON” position. If the problem persists replace the gas valve.

Eight-Three Flash, three second pause Electronic Fault Detected Turn the power switch on the gas control valve to the “OFF” position, wait 10-20 seconds then turn the

power switch on the gas control valve to the “ON” position. If the problem persists replace the gas valve.

Eight-Four Flash, three second pause Gas Control Valve/Thermostat Fault Detected Turn the power switch on the gas control valve to the “OFF” position, wait 10-20 seconds then turn the

power switch on the gas control valve to the “ON” position. If the problem persists replace the gas valve.

* Soft Lockout - 20 minute wait before returning to normal mode.

1 2 ... 27 28 29 30 31 32 33 34 35 36 37 38 39 40

Kommentare zu diesen Handbüchern

Keine Kommentare

Reliant FVIR GAS WATER HEATER Gebrauchs- und Pflegeanleitung Seite 32

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Warmwasserbereiter & Kessel Reliant FVIR GAS WATER HEATER