Reliant FVIR GAS WATER HEATER Bedienerhandbuch PDF herunterladen (Seite 20)

FOR YOUR SAFETY READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or

explosion may result causing property damage, personal injury or loss of life.

LIGHTING INSTRUCTIONS

1. Set thermostat to the lowest setting.

TO TURN OFF GAS TO APPLIANCE

BEFORE LIGHTING: ENTIRE SYSTEM MUST BE FILLED WITH WATER AND AIR PURGED AT FAUCETS.

2. Push gas control knob down slightly and turn clockwise

to “OFF”, see Figure A. Do not force.

TOP VIEW

FIGURE D.

GAS CONTROL

A. This appliance has a pilot which must be lighted by hand.

When lighting the pilot, follow these instructions exactly.

B. BEFORE LIGHTING: smell all around the appliance area

for gas. Be sure to smell next to the floor because some

gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electric switch; do not use

any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call the

fire department.

C. Use only your hand to push down or turn the gas control

knob. Never use tools. If the knob will not push down or

turn by hand, don’t try to repair it, call a qualified service

technician. Force or attempted repair may result in a fire

or explosion.

D. Do not use this appliance if any part has been under

water. Immediately call a qualified service technician to

inspect the appliance and to replace any part of the

control system and any gas control which has been

under water.

1. STOP! Read the safety information above on this

label.

2. Set the thermostat to the lowest setting by turning

thermostat dial fully clockwise

until it stops.

3. Push the gas control knob down slightly and turn clockwise

to "OFF", see Figure A.

NOTE: Gas control knob CANNOT be turned from "PILOT"

to "OFF" unless it is pushed down slightly. Do not force.

4. Remove the inner and outer doors located below and

behind the gas control unit.

5. Wait five (5) minutes to clear out any gas. If you then

smell gas STOP! Follow "B" in the safety information

above on this label. If you do not smell gas, go to

the next step.

6. Find Pilot. Follow metal tube from the bottom, right of the

gas control to the pilot burner (Figure D).

7. Turn gas control knob counterclockwise

to "PILOT",

see Figure B.

8. Push gas control knob down all the way and hold it down.

Immediately light the pilot with a match. Continue to hold

the gas control knob down for about one (1) minute after the

pilot is lit. Release the gas control knob and it will pop back

up. Pilot should remain lit. If it goes out, repeat Steps 3 through

8. It may take several minutes for air to clear the lines, before

the pilot will light.

• If knob does not pop up when released, stop and

immediately call your service technician or gas

supplier.

• If the pilot will not stay lit after several tries, turn the gas

control knob to "OFF", see Figure A and call your service

technician or gas supplier.

9. Replace inner and outer burner doors.

10. At arm's length away, turn gas control knob

counterclockwise

to “ON”, see Figure C.

11. Set thermostat to desired setting, (See Figure 1).

CAUTION: Hotter water increases the risk

of scald injury. Consult the instruction

manual before changing temperature.

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 ... 31 32

Kommentare zu diesen Handbüchern

Keine Kommentare

Reliant FVIR GAS WATER HEATER Bedienerhandbuch Seite 20

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Warmwasserbereiter & Kessel Reliant FVIR GAS WATER HEATER