Reliant Octel 200 Bedienungsanleitung PDF herunterladen (Seite 8)

PAGE 7

# CODE FEATURE

SYSTEM PARAMETER TABLE

1 Installation name

2 System ID number

3 PBX type/PBX model

4 Voice ports used/Fax channels used

7 Reprompt limit

8 Backup/go ahead time (blocks)

9 Flash time (milliseconds)

12 Install question number

13 Transfer initiate code

Re-connect code after no answer

Re-connect code after busy

Re-connect code after fast busy

Transfer complete code

16 Alternate transfer initiate code

Alternate re-connect code after no answer

Alternate re-connect code after busy

Alternate re-connect code after fast busy

Alternate transfer complete code

19 Mailbox numbers match user extensions

22 Default message waiting start hour

23 Default message waiting end hour

25 Default message waiting retry period (minutes)

26 Double-interrupted ringback

28 "D" character delay time (milliseconds)

31 Alarm number

32 Maximum message length (minutes)

33 PBX initialize code

43 Personal greeting 1=no call 2=call first

45 System-reload forward string

46 System-reload cancel forward string

51 AI RS-232 integrated with PBX

56 Number of transfer retries if flash fails

58 DID/EM DEV: Device support

Master system

59 DID/EM DID: System pilot extension number

60 DID/EM DID: Attendant extension number

61 DID/EM DID: Number of digits expected from CO

62 RAN NET: Night delivery start time

63 RAN NET: Night delivery end time

64 NET: Max beeps for multicabinet connect

65 NET: Multicabinet delivery attempt limit

66 NET: Multicabinet delay before retry (minutes)

67 VNET NET: Max beeps for remote connect

68 VNET NET: Remote delivery attempt limit

VNET/ONET

NET:

Remote delay before retry (minutes)

70 RAN NET: Message delivery mode default

71 Tone-detect threshold

72 Lines-per-page for reports

73 Minimum length for message to be sent (blocks)

74 Initial silence max seconds (quick/scripted)

75 Subsequent silence max seconds (quick/scripted)

76 Novice prompt keypad command usage limit

77 PBX provides momentary disconnect

78 PBX provides stutter dial tone

79 Lamp MW: "ON" pre-extension digits

80 Lamp MW: "ON" post-extension digits

81 Lamp MW: "OFF" pre-extension digits

82 Lamp MW: "OFF" post-extension digits

83 Lamp MW: Light lamp for each new message

84 Lamp MW: Call ext before lighting lamp

85 Reconnect code after 3rd party hung-up

86 Callers get music-on-hold

87 CQ Maximum retries when FIFO queuing

88 NET: Initial digits include mailbox 1st digit

89 VNET NET: Use trunk reconnect codes

90 VNET NET: Reconnect code after trunk access

91 VNET NET: Reconnect code after 3rd party hang

92 VNET NET: Complete transfer to trunk

93 ICR Send account code to PBX digits

94 ICR Reconnect after account code digits

95 PBX accepts DTMF digits on DID trunk

96 Move backward during greeting (blocks)

97 Move forward during greeting (blocks)

98 Default language

99 Ringbacks before answering CX port

100 Ringbacks before answering MX port

101 Delay before turn on DTMF report (milliseconds)

102 Pager access digits

103 VNET NET: Remote delay before DTMF signaling

104 NET: Multicab delay before DTMF signaling

105 Default security code for mailbox logon

106 Lamp MW: Port for lamp message waiting

107 PBX never gives partial ringback or busy

108 Disk usage threshold before alarm notification

109 RNG Store greeting messages redundantly

110 RNG Store name messages redundantly

111 Dial extension after reconnect code

112 Send DTMF A on CX/MX ports

113 Max silence for special purpose greetings (seconds)

114 DEV: Delay before intercepting calls

115 System says "on the phone" instead of "is busy"

116 AI Integration active

117 Ringbacks before answering AX port

118 E&M E&M: Length of record (network)

119 E&M E&M: Number of ext digits expected (direct)

120 E&M E&M: Number of ext digits expected (network)

121 E&M E&M: System pilot ext number (direct)

122 E&M E&M: System pilot ext number (network)

123 E&M E&M: Attendant ext number (direct)

124 E&M E&M: Attendant ext number (network)

125 E&M E&M: Number of digits before ext (network)

126 E&M E&M: Number of digits before location code (net)

127 E&M E&M: Location code

128 Send mailbox to PBX rather than extension

129 NET: Limit on line quality test

130 AI Send DTMF A for forwarded calls

131 Speak "Dial zero for assistance"

132 CQ Speak system prompts for FIFO queuing

133 AI Integration card extension

134 Ignore DTMFs after entering ext number

140 Maximum forwarding depth

141 Can use 0 as wildcard in name

142 Minimum letters required for name

143 UI 5000 ui: Group code (PDL) first digit

144 Minimum length for security codes

145 W Application processor error mailbox

146 W Application processor installed

147 Names directory mailbox

149 Allow blind transfer to personal assistance

150 Remove "connect" for announce to intercept

151 Remove "status" for announce to intercept

152 VNET NET: Remove network prompt for quick logon

153 Delay on CX port before playing greeting

154 Remove "status" after call first greeting

155 Ignore line drop after call start (seconds/10)

156 W Application processor message pool EMB list

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Kommentare zu diesen Handbüchern

Keine Kommentare

Reliant Octel 200 Bedienungsanleitung Seite 8

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Server Reliant Octel 200